Tekno RC M6 Driveshaft & Hub Carrier Set (Rear, 6mm)

Ive seen several people with these on the stampede 4x4 with no problems. Also the slash and stampede are identical in the driveline only thing difference between the two trucks is the chassis,bumpers,wheels/tires,rx box, front body mount and body otherwise they are the same. If they didn't fit the stampede must have something set up wrong.

I absolutely love these in my Slash 4x4 running the Viper 5150Kv 4-pole setup on 2S. No pins to break like on the MIP's - I have had no issues with the driveshafts themselves even when flat-landing 10-foot jumps at full throttle. The one issue I have had is that the shafts are so good that now you wheels and hexes are your drivetrain's weakest point. MAKE SURE your wheel nuts are tightened securely or your hex and wheel will end up rounded.
I also want to point out that these even come with upgrade bearings for better power handling and new caster blocks to house the bearings - it is a very complete set and I have been happy with it from the get-go. Where are those features MIP? Great job Tekno! I highly recommend these.

Used to have the mip x-duty and they were horrible. Switched to these because od direct drive and was very impressed. They use the stock outdrive set screws which is very nice. Have used them for over 3 months now and they have stood up the switch from the stock vxl to an insane castle 3800 motor. Very impressed. Just make sure you use some more negative camber or lose some preload to prevent them from popping out of the cups.
These are a must have upgrade for the stampede 4x4.

These are such an improvement over stock. Mine wear like "iron" so far. Would never go back to stock. I guess Traxxas would not either since in the 1/16 Slash they run a similar design, dumping the plastic "bind-shafts" on the 1/10 Slash...

been running this for about a month. No problems no sign of wear. Best rear driveshaft on the market right now.

Running these on a slash 4x4 vhl on 3s and so far so good. Stock won’t last one 2s battery and I’ve ran several 3s through these already. Excellent for the price. No vibrations either, unlike the mips.

These driveshafts are amazing. They build easily and are a perfect fit. My slash now accelerates better and the new shafts handle strain much better. Great Product and Great Customer Service from Amain!

i have had these for a couple years now front and rear 2s and 3s lipo these are the axles for your slash 4x4 i have rpm arms and a locked tight slipper there tuff in water dirt street what ever you have you not hurting these

My truck takes a ton of bashing at a 1/8th scale track and just overall bashing. It is great that they are captured so I don't lose them when I break a control arm. I also throw 4s at them every once in a while with no complaints.

Awesome upgrade very tough, running on 3s zero issues front and rear installed flawless.

Fast delivery to Russia! 13 days! The set of drives is excellent! You can see the quality is amazing!

Amazing Driveshafts for the money. They are easier to assemble than the MIP shafts and have held up just as well on a 2650kv motor and 3s. Would reccomend as an affordable upgrade for traxxas 4x4 trucks

I bought these about a year and a half ago and I love them they are better than MIP's if you ask me because the pins fly out of them but the only thing I would upgrade would be hex hub to aluminum from tekno

The slash & stampede aren't the same are they ?! Maybe you should read before you buy smart guy !!!!!!!

Not sure if it because i am running RPM rear A-Arms, or what but these things; (the shafts), are about 1/8" to short. Any jumping that is done the Driveshaft falls out of the carrier next to the Transmission case. Either the M6 Rear Hubs need to have another hole on the bottom mount side Closer to allow the Driveshaft to seat fully, or ________??? any ideas would be awsome. If you can help a brother out with this issue here is my email that i check every once in a while. Datastream1979 at gmail.com.

Other than that they work great, when they work.

Don't buy them! I tried these on my Stampede 4x4 and I imediately realized, after puting them together, that the dog bones are WAY too short. It could be the RPM arms are longer than the stock ones too. Also, you have to run these with the plastic Tekno hubs. I have ST Racing aluminum hubs and they dont work with this set up. Invest a little more money on the MIP set up. I wish I did.